Bubble Wrap Rolls

GREY Gloss, Matte Vinyl Wrap Sheet Car Wrap. This vinyl will give your vehicle a new look with a matte finish or Gloss finish. Can be used to wrap a section of your vehicle or the entire car body depending on your preference. Permanent acrylic pressure-sensitive adhesive can be re-lifted, repositioned and stretched Stretchable with heat Conform to contours and bends easily High temperature & water resistant can be washed with soap and water Stands up against water, dirt, grease, salt, mild acids. Long life with excellent UV durability (up to 3 years). Make sure you have images of the vehicle prior to planning the design. Determine where all the joins will fall (if any). Use the natural lines of the vehicle, whether horizontal or vertical. Use door panels/weld lines to cover overlaps and ensure if the film is textured, such as brushed steel or carbon fibre, that the grain will run in one direction, usually front to back. Thoroughly wash the vehicle down with soap and water, removing any wax coating, dirt and grime, especially in deep crevasses and door jambs. Degrease the vehicle with a 3M or Avery isopropyl alcohol surface cleaner. Surface cleaners are usually fast drying so each complete panel can be done directly prior to wrapping it to ensure from the time it is cleaned, to the time the film is layed on the panel, no dust or dirt will have a chance to stick to the surface. For solvent printed media allow a minimum of 48hrs to outgas. The rolls should be left standing vertically and loosely wound (print side out) to help with airflow and should be turned regularly as the solvents are heavier than air. The more the vinyl can be allowed to de-gas, the less tacky the adhesive will feel and the easier the graphic will be to fit. Laminate with cold rollers only. Do not use excessive tension on the rollers. Use a hard velvet edged squeegee or similar to avoid scratching. Apply the vinyl to the flattest part of the panel first (create a base line) working from side to side, keeping the vinyl as level as possible. Stretch the vinyl without heat over the whole area and do not work the film into the more complicated areas such as recesses until later. When stretching the vinyl, always pull outwards from the largest area of the vinyl you can to spread the tension. This also applies when you use extra heat to soften and stretch the vinyl, apply heat to a larger area than you need as this should help to avoid distorting the graphic. Try not to cut the vinyl directly on the body of the vehicle, but if you must, when cutting through the vinyl on the bodywork or around handles you can stick electrical tape to the surface first for depth control. Use a new blade each and every time you cut through the vinyl. The weight of the blade should be enough without having to apply extra pressure. Post heat to 95ºC or above and unless you have had extensive experience, try to always use an infra red temperature gauge to be sure that you have reached this temperature. Anything less and the vinyl will retain its memory and cause the graphic to pop out of recesses and curves. This post heating must be carried out scrupulously on all areas where the wrap has been stretched to fit, especially in deep recesses. Do not overheat as you may damage the film. If vehicle wrapping in colder weather it is sometimes better to ensure the vehicle doesnt leave the workshop until the following day. The vehicle and vinyl should be allowed to cool down at the same rate as the workshop. This will help to avoid thermal shock and reduce the risk of failure in the recesses. For those harder to reach destinations and outside Europe, we request your patience as it may take longer than expected. We will then provide you with instructions that will help us process your case efficiently. The item must be unused and in its original packaging. This varies per each country. As an international customer you are responsible to consult your country’s import policy and regulations since these are not included in our prices; these are your sole and exclusive responsibility and should be paid to your custom agency or in certain cases to the courier company. The item “GREY Gloss, Matte Vinyl Wrap Sheet Car Wrap’Air Bubble Free’ Car wrapping UK” is in sale since Wednesday, September 5, 2018. This item is in the category “Home, Furniture & DIY\DIY Materials\Wallpaper & Accessories\Wallpaper Rolls & Sheets”. The seller is “skymex-uk-ltd” and is located in Stockport. This item can be shipped to all countries in Europe, all countries in continental Asia, United States, Canada, Australia.

• Gender: car
• Country/Region of Manufacture: United Kingdom
• Style: vinyl
• Material: Vinyl
• Type: Vinyl wrap
• Features: Gloss
• MPN: Does Not Apply
• Finish: Vinyl Coated
• Room: Car
• Type of Packaging: Roll and sheet
• Brand: skymex
• Design: Plain