Thank you for viewing my listing. DOUBLE SIDED SILVER FOIL. TWO LAYERS OF FOIL. REDUCE RADIANT HEAT TRANSFER. IDEAL FOR HOT OR COLD CLIMATE. 75 SQUARE METERS (825 SQUARE FEET). 10 MM (3/8) DIAMETER BUBBLES. 4 MM THICK (3/16) BUBBLES. TWO LAYERS OF ALUMINUM FOIL. Call Eddie Solomon if you have any question. Please Note: this product does not comply with Australian Standards nor the Building Code but it is tested by Australian CSIRO and has been used widely for home insulation. TO VIEW ALL FOIL BUBBLE INSULATION. SILVER FOIL BUBBLE INSULATION. Double Foil Insulation is available in 75 Square Meters rolls – 1,500 mm wide x 50 Meters long. It consists of a layer of polyethylene bubbles that is sandwiched between two layers of 99% pure aluminum radiant barrier foil. This style can be used in a variety of applications because it’s light weight and easy to handle yet provides superior protection. The bubble center creates maximum R-Value and the reflective foil on both sides allow it to reflect 97% of radiant heat away from a structure on the outside and back in on a structure from the inside. This is why it works effectively in both hot and cold climates. Double Foil Reflective Insulation is a versatile insulation consisting of an 4.8 mm thick – 10 mm diameter layer of polyethylene bubbles sandwiched between two sheets of highly reflective, 99% aluminum. Reflective Bubble Insulation provides superior reflectivity of radiant heat while providing protection against conductive heat gain and loss as well as performing as a vapor barrier. Nominal Thickness 1/4 – 0.6 mm. Weight 0.5 oz / sq. Ft – 160 g/sq m. Temperature Range – ASTM C411 -50 F to 180 F (-45 c to 82 c). Flame Spread (ASTM E84-05) 5. Smoke Development (ASTM E84-05) 5. Emissivity – ASTM C1371 0.03-0.04. Reflectivity – ASTM 3903 0.96-0.97. Water Vapor Permeance-ASTM E96. Flexibility – No Cracking. Resistant to Fungi and Bacteria Does not promote growth. ADVANTAGES OF THIS PRODUCT. Very effective in warmer climates. No change to thermal performance over time due to compaction, disintegration or moisture absorption. Thin sheets takes up less room than bulk insulation. Can act as a vapor barrier. Will not mold or mildew. Radon retarder, will limit radon penetration through the floor. This is a high quality industrial strength Double Foil Insulation Bubble Wrap. Long lasting, heavy duty nylon barrier layer to increase longevity. Bubble Wrap is Lightweight and easy to use. It is an inexpensive solution to your insulation needs. This 75 Square meter Silver Insulation Foil Bubble Wrap usually comes in rolls of 1,500 mm wide. However, it may come in other widths totalling 75 Square meter depending on availability. Our standard single and double bubble foil insulation is. Silver foil Available in a range of widths, from. 375 mm 15″ to 1,500 mm (60″), and lengths. We offer double-sided Silver. Aluminium products, as well as products covered with Silver Foil. On one side and white polyethylene on the other. This durable bubble insulation will withstand temperatures between -50 degrees Celsius. And 82 degrees Celsius (180 degrees Fahrenheit), making it ideal for both attic and flooring installations. Be sure to check out our silver Foil Aluminium. This is the best tape for bubble foil insulation because it ensures the continuity of the reflective surface, which is essential for getting the most from your installation. Radiant floor heating has been in use for centuries and radiant barriers help to retain the heat generated by the radiant heating system blocking it from escaping into the ground. Silver foil bubble Wrap. Insulation is extremely tough and pliable, easy to install, and is an excellent vapor barrier for all your radiant floor heating applications, thus greatly reducing your electricity or gas bills. Silver Foil Bubble wrap. Insulation installed in crawl spaces below a building structure reflect the heat flows that are flowing downward from the flooring back up into the flooring at a 95-97% rate providing increased comfort and heat retention. The temperature of the cold floors which cause cold feet will be raised while your heating bill is reduced, providing for increased comfort. As heat is reflected back into the living area, it warms other objects which then radiate heat back into the room, further increasing your living comfort. Metal & Steel Buildings. Temperature sensitive storage areas. Silver foil Bubble Wrap. Insulation applications are only limited by your imagination. The main feature of this insulation is its reflective nature and not the thickness of the material. It has a nominal thickness of 4.8 mm and easy to handle. We can also custom make any combination to suit your requirements. You can have foam sandwiched between two layers of Silver foil, Or thicker bubbles between tow layers of foil, or any combination you require. Please note custom made insulation attracts minimum order of 1,500 Square meters. Custom orders are final. All the insulation is made right here in Australia with the highest standard of material and manufacture. The following Test Report conducted by the Australian CSIRO on the single Foil Bubble Insulation. This listing is for the Double Foil Bubble Insulation which commands a higher insulation quality tham the single. CSIRO- Materials Science & Engineering. (ABN: 41 687 119 230). Henry St, Belmont, Victoria 3216, Australia. Page 1 of 1. Sample Description: silver insulation material designed for pallet protection. At an ambient temperature of 23.1ºC – difference from face to back 2.4ºC. At an ambient temperature of 28.6ºC – difference from face to back 5.1ºC. OF THE INSULATIVE EFFECTIVENESS OF SINGLE-SIDED 10 MILLIMETRE BUBBLE FILM (4.8 mm Thick). LAMINATED WITH METALLISED P. THE TRUTH ABOUT R VALUE. Around most of the world, R-values are given in SI units, typically square-metre kelvin per watt or m2·K/W (or equally, m2·°C/W). In the United States customary units, R-values are given in units of ft2·°F·hr/Btu. It is particularly easy to confuse SI and US R-values, because R-values both in the US and elsewhere are often cited without their units, e. Usually, however, the correct units can be inferred from the context and from the magnitudes of the values. United States R-values are approximately six times SI R-values. The conversion between SI and US units of R-value is 1 h·ft2·°F/Btu = 0.176110 K·m2/W, or 1 K·m2/W = 5.678263 h·ft2·°F/Btu. As an example an R11 in the United States is approximately R2 in SI units in Europe, Australia and the rest of the world. An R value advertised by a United States merchant may appear more appealing as the US R value is 6 times higher than SI values used in the rest of the world. It does not mean that a US R value is more effective than An R value used in Europe, Australia or the rest of the world. Do not rely on the R value provided by the supplier as the R value may increase or decrease depending on the application. Furthermore, the actual R value of the insulation depends entirely on the application and how you apply the insulation. An R 2 value may increase or decrease depending on how the insulation is applied. With the Silver Foil bubble Insulation you will need an air pocket between the surface. Of the structure you are insulating. And the insulation material. The air pocket has its own r value depending on the width of the air pocket thus increasing the R value of the insulation material. Conversely, if you apply the insulation material directly on the surface of the structure will defeat the purpose of insulation because the insulation material will act as a heat conductor and will end up heating the premises in the hot summer and will also be counterproductive in winter. Radiation is minimized by low emissivity (highly reflective) exterior surfaces such as aluminum foil. Lower thermal conductivity, or higher R-values, can be achieved by allowing an air gap between the surface of the structure and the aluminium foil. The air gap will act an heat pocket where heat will accumulate instead of being circulation inside your structure. Trapped air has its own R value. The R value of trapped air depends on how much gap is between the insulation material an the structure. A wider gap will produce a greater R value and a narrower. Gap will produce a smaller R value. Air by itself has no R value; only trapped air will produce an R value. However, if you allow a very wide gap, the air will not be trapped and may reduce your R value and cause an opposite result. The R-value is a measure of an insulation sample’s ability to reduce the rate of heat flow under specified test conditions. The primary mode of heat transfer impeded by insulation is conduction, but insulation also reduces heat loss by all three heat transfer modes: conduction, convection, and radiation. The primary means of heat loss across an uninsulated air-filled space is natural convection, which occurs because of changes in air density with temperature. Insulation greatly retards natural convection making the primary mode of heat transfer conduction. To find the heat loss per square meter, simply divide the temperature difference by the R value. If the interior of a home is at 20 °C, and the roof cavity is at 10 °C, the temperature difference is 10 C° (= 10 K difference). Assuming a ceiling insulated to R-2 (R = 2.0 m2K/W), energy will be lost at a rate of 10 K/2 K·m2/W = 5 watts for every square meter of ceiling. Doubling the thickness of the insulation material or even doubling the thickness of the trapped air layer doubles the R value. This does not hold for compressed bats of glass wool because compressing the bats does not proportionally increase the r value. Furthermore, doubling the thickness of the Silver Foil Bubble Insulation does not double the R value of the insulation material. The main feature of the Silver Backed Bubble Insulation is its reflective nature and not its thickness. To Double the R value of the Foil Bubble Insulation you will need to create a heat pocket which hads it s own R value that can be added to the R value of the Foil Insulation. As an example, the if Foil Bubble Insulation has an R value of r2 and the. Heat pocket has an R value of R 1,5, both R value are added together to achieve an R value of R3.5 in SI units or R19 in United States standards. As discussed earlier porous material such as foam and bats does not allow the full potential of trapped air to be established and will not give you the proportional R value relative to thickness. In calculating the R-value of a multi-layered installation, the R-values of the individual layers are added:[10]. R-value(outside air film) + R-value(brick) + R-value(sheathing) + R-value(insulation) + R-value(plasterboard) + R-value(inside air film) = R-value(total). To account for other components in a wall such as framing, an area-weighted average R-value of the whole wall may be calculated. For the most part, testing the R-value of insulation is done at a steady temperature, usually about 70 °F (21 °C) with no surrounding air movement. Since these are ideal conditions, the listed R-value for insulation will almost certainly be higher than it would be in actual use, because most situations with insulation are under different conditions. Some types of foam insulation, such as polyurethane and polyisocyanurate are blown with heavy gases such as chlorofluorocarbons (CFC) or hydrochlorofluorocarbons (HFCs). However, over time a small amount of these gases diffuse out of the foam and are replaced by air, thus reducing the effective R-value of the product. This has led to controversy as how to rate the insulation of these products. Many manufacturers will rate the R-value at the time of manufacture; critics argue that a more fair assessment would be its settled value. [citation needed] The foam industrywhen? Adopted the LTTR (Long-Term Thermal Resistance) method, [14] which rates the R-value based on a 15 year weighted average. However, the LTTR effectively provides only an eight-year aged R-value, short in the scale of a building that may have a lifespan of 50 to 100 years. Note that these examples use the non-SI definition and/or given for a 1 inch (25.4 mm) thick sample. Vacuum insulated panels have the highest R-value (approximately R-45 per inch in American customary units); aerogel has the next highest R-value (about R-10-30 per inch), followed by isocyanurate and phenolic foam insulations with, R-8.3 and R-7 per inch, respectively. They are followed closely by polyurethane and polystyrene insulation at roughly R-6 and R-5 per inch. Loose cellulose, fiberglass (both blown and in batts), and rock wool (both blown and in batts) all possess an R-value of roughly R–2.5 to R–4 per inch. Straw bales perform at about R-1.5. However, typical straw bale houses have very thick walls and thus are well insulated. Snow is roughly R-1. The effective thermal resistance of an enclosed air cavity is strongly influenced by radiative heat transfer and distance between the two surfaces. All quality products at bargain prices. Occasionally, I list the same item with discounted prices for a limited time. Please Note: Due to the bulky size of this insulation, the 75 Square Meters are sent as follows. 1 Roll of 75 square meters – 1,500 mm wide 50 m long. 2 Rolls of 37.5 Square meters – 1,500 mm wide 25 m long each. 2 rolls of 37.5 Square meters each – 750 mm wide 50 m long. Public holidays and weekends excluded. However, there is no guarantee that you will receive your parcel by the estimated date. The most economical method. If you wish to have your item delivered or handled in a special manner, let me know and I will inform you if there is any additional charge. If you live in a remote location with no courier service, let me know. Delays may be experienced in case of work overload, postal or courier. Delays, public holidays and weekends, or shortage of stock. If premises unattended, leave in a secure location. If premises unattended, place a card in the mailbox and leave parcel at nearest collection point. The parcel shall be deemed to have been delivered. If the parcel is sent by courier, a signature is usually required. You can select that the courier leaves the parcel. If it is not safe to leave the parcel by Your front door, then you will need to sign for it. All parcels will be securely packaged. For its loss or damage. Otherwords, all care taken and no responsibility accepted. No responsibility can be taken if you fail to provide a telephone number. Please note, I assume no responsibility if the item is delayed, lost or damaged n transit. No compensation will be paid until such investigation has been concluded. You will also need to arrange for your own packaging. International Buyers – Please Note. I strive to please my fellow eBayers. If you have any issue with the item, let me know. Errors & Omissions Excluded. No other warranties either expressed or implied are offered. You may find similar items cheaper with other sellers or retailers. I also rely on sighted assistants to help with the pictures and description. If you prefer to trade with a behemoth, please go elsewhere. From time to time I offer the same item cheaper for a limited period. The description of the items is as provided by the principal sellers and believed to be reliable. All feedback will be reciprocated. If you are happy with my service, tell the whole world, if you are not happy, tell me. If you have any issue with the item, contact me first before you post negative or neutral feedback. Issues can be resolved amicably. Leaving damaging feedback before your attempt to resolve any issue first will be deemed as defamatory and in contravention of the terms and conditions and will be dealt with accordingly. The bad Karma will result in proceedings for the removal of such feedback and will give rise of a liquidated claim for damages. Any unwarranted negative or neutral feedback will be removed using legal processes and may give rise to a liquidated claim for defamation or/ and breach of contract. All issues can be resolved amicably. An issue, contact me first. If you have any issues with your item, let me know and I will be happy to rectify any problem. If you post negative or neutral feedback without first letting me know of your intention to post such feedback will be deemed defamatory and may give rise to proceedings for defamation and/or breach of contract and will give rise to a liquidated claim for damages. If you have in issue, it would be quicker to contact me first and I will do my utmost to help you. If you do not wish to have feedback posted for you – for privacy reasons or otherwise – just let me know and I will not post feedback for you or simply do not post feedback for me. All brand names & trademarks are the property of their respective holders and are referred to here for descriptive purpose only. The listed brand names and model designations are intended only to show the compatibility of these products with various products. Pictures are for descriptive purposes only. All dimensions and measurements are approximate. Colour is as shown unless otherwise stated. Colour may vary depending on lighting, your computer screen resolution or angle of viewing. Please exercise care when you open your package when you receive it. Do not slash the packing material with a knife as to damage the contents of the package. Open carefully so you don’t drop the contents in case of fragile or breakable items. If the information is not correct, please provide your correct contact information. You agree to abide by the herein Terms & Conditions and any further amendments. Any dispute arising out of this. Agreement or the interpretation thereof. Shall be decided and. Settled in accordance with the laws and statues of the State of New South Wales, Australia. The parties agree that the venue shall be Sydney, New south Wales. This item is in the category “Home & Garden\Other Home & Garden”. The seller is “eddiesolomon777″ and is located in this country: AU. This item can be shipped worldwide.
- Product Type: Silver Foil Bubble Wrap Insulation
- Modified Item: No
- Style: Double Sided Foil
- Custom Bundle: No
- Type: Roll
- MPN: SFBI2
- Brand: EDDIE SOLOMON
- UPC: 722197213239
